American Water Heater UP300 Specifications download pdf (Page 26)

Attic Roof Insulation (Pre-notification required)

This rebate is available to industrial end-use customers who utilize boilers as an integral part of a manufacturing process.

Boilers must meet a minimum combustion

efficiency of 82 percent as installed. Only process boilers (i.e., units not primarily

used for domestic hot water, space conditioning, pool or spa use) qualify. The manufacturer name and equipment model

number must be provided. A flue gas analysis measured under full load conditions is required to document combustion

efficiency after installation is complete.

Flat Roof Insulation (Pre-notification required)

This incentive is for adding insulation to existing buildings. Total roof area must be less than 150,000 ft

Roof insulation

must be installed in a space that requires natural gas fired space heating. All materials must be new and meet applicable

state and local codes and must be installed in accordance with the manufacturer’s requirements. "Insulation Entirely above

Deck” and “Metal Building" (as defined by ASHRAE 90.1 2007) roof insulation is eligible for the incentive only when it is

installed between the conditioned and unconditioned areas. Insulation installed above dropped commercial ceilings is not

eligible. Pre-retrofit insulation levels must be less than R-11 and final insulation assembly level must exceed R-24 and/or

local building codes. Pre-Applications will require the following: a) a scaled floor plan of the facility’s total roof area (ft

) being

insulated, b) a roof construction detail (sketch) showing a section cut of the existing roof, c) roof construction detail (sketch)

showing a section cut of the proposed roof, and d) specifications of the proposed roof insulation. Pre-construction pictures

of the condition of the existing roof insulation would also be beneficial. The maximum incentive available for this measure is

$20,000 per facility as defined in the policies and procedures manual. Buildings with a roof area larger than 150,000 ft

are

eligible for a custom incentive.

This incentive is for adding insulation to existing buildings. Roof insulation must be installed in a space that requires natural

gas fired space heating. All materials must be new and meet applicable state and local codes and must be installed in

accordance with the manufacturer’s requirements. "Attic and Other" (as defined by ASHRAE 90.1 2007) roof insulation is

eligible for the incentive only when it is installed between the conditioned and unconditioned areas. Insulation installed above

dropped commercial ceilings is not eligible. Pre-retrofit insulation levels must be less than R-11 and final insulation

assembly level must exceed R-42 and/or local building codes. Pre-Applications will require the following: a) a scaled floor

plan of the facility’s total roof area (ft

) being insulated, b) a roof construction detail (sketch) showing a section cut of the

existing roof c) roof construction detail (sketch) showing a section cut of the proposed roof and d) specifications of the

High Efficiency Process Boile

Page 26

Rev. Mar 30, 2011

This incentive applies towards the replacement of an existing conveyor-based gas broiler. New construction projects do not

qualify for a rebate with this measure. Existing broiler must be removed and disposed of in accordance with local and state

codes.

Wall insulation must be installed in a space that has natural gas fired space heating. All installed materials must be new and

meet or exceed all applicable local, state, and federal standards. To qualify existing walls cannot be insulated. The final

insulation levels should exceed R-13 and/or local code for the building type. Incentives will be paid on total square footage

of wall insulation.

A conveyor oven can be described as a heated chamber with a moving belt that carries food product into and through the

chamber. The commercial oven(s) must meet or exceed baking energy efficiency of 42 percent. Ovens with a conveyor

width up to 25” in length must have an idle energy rate of less than or equal to 29,000 BTU/H. Ovens with a conveyor width

over 25” in length must have an idle energy rate of less than or equal to 57,000 BTU/H. Multiple-deck oven configurations

are paid per qualifying oven deck. Used or rebuilt equipment does not qualify.

Wall Insulation (Pre-notification required)

Flexible Batch Broilers

Commercial Conveyor Ovens

isting

roof

constr

ction

detail

(sketch)

sho

ing

section

the

proposed

roof

and

specifications

the

proposed roof insulation. Pre-construction pictures of the condition of the existing roof insulation would also be beneficial.

The maximum incentive available for this measure is $15,000 per facility as defined in the policies and procedures manual.

1 2 ... 21 22 23 24 25 26 27

Comments to this Manuals

No comments

American Water Heater UP300 Specifications Page 26

Comments to this Manuals

Related products and manuals for Water heaters & boilers American Water Heater UP300